SECTION 224233 - WASH FOUNTAINS

BRADLEY WASHFOUNTAINS

Bradley Corporation, a leader in the manufacture of fixtures andplumbing products, provides a variety of commercial wash fountains for everycommercial and industrial need. Constructed of Bradley's premium Terreon solidsurface material, with options for recycled content solid surface material, or reinforcedthermoset polyester, precast terrazzo, or stainless steel, Bradleywashfountains are manufactured to last for years and remain serviceable at theend of a long career.

Architects, engineers, and specifierslook to Bradley Corporation for innovation in design and leadership in thedevelopment of environmentally conscious products.? Bradley Corporation, a member of the U.S.Green Building Council, the Wisconsin Green Building Alliance, has severalproducts earning certification by Greenguard Environmental Institute, andGreenguard Children and Schools program.

Bradley makes it easy to specify products providing a seasonedcustomer service staff, and helpful information toolson an advanced website.? Bradley is theindustry leader in the manufacture of premium quality commercial plumbingfixtures, valves, TMVs and wash fountains that appear in the following CSIMasterFormat 2004? Sections:

Section 10 21 13? Toilet Compartments (Mills Metal, Plastic-laminate, Phenolic, and Plasticunits)

Section 10 28 13.13? Commercial Toilet Accessories

Section 10 28 13.15? Hand and Hair Dryers

Section 10 28 13.63? Detention Toilet Accessories

Section 10 51 26.00? Plastic Lockers (Lenox Plastic Lockers)

Section 10 51 26.13? Plastic Lockers (Lenox Recycled Plastic lockers)

Section 22 11 19? Domestic Water Piping Specialties (Thermostatic mixing valves)

Section 22 42 16.01? Commercial Lavatories and Faucets (Single and multi-station lavatory systems)

Section 22 42 16.02? Commercial Lavatories and Faucets (Bradley Advocate Lavatory System)

Section 22 42 16.03? Commercial Lavatories and Faucets (Bradley Verge Lavatory System)

Section 22 42 16.11? Commercial Sinks and Faucets

Section 22 42 23? Commercial Showers and Shower Valves

Section 22 42 33? WashFountains

Section 22 43 00? Healthcare Plumbing Fixtures (Patient care lavatory units)

Section 22 45 00? Emergency Plumbing Fixtures (Emergency EyewashFixtures and Drench Showers)

Section 22 46 00? Security Plumbing Fixtures

Contact Bradley Corporation, Menomonee Falls, WI 53051;Phone: 800-BRADLEY ((800)272-3539) Fax:? (262)251-5817,or visit the Bradley web site www.bradleycorp.com.

Bradley Corporation is an AIA/CES registered provider currentlyoffering five programs earning one (1) HS&W Learning Unit each; severalqualify for sustainable design (SD) credit.?All active AIA members must successfully complete 18 learning unit (LU)hours each year.

Terreon?is a registered trademark of Bradley Corporation.

TouchTime? is atrademark of Bradley Corporation

SECTION 22 42 33

WASH FOUNTAINS

PART 1 - GENERAL

1.1 SECTION INCLUDES

1. Wash Fountains.

1.2 RELATED SECTIONS

1. Division 22 Section "Domestic WaterPiping Specialties" for thermostatic mixing valves.

1.3 REFERENCES

A. American National Standards Institute (ANSI):

1. ANSI Z124.3 Plastic Lavatories.

2. ANSI Z124.6 Plastic Sinks.

3. ANSI/ICPA SS-1-2001 Performance Standard for SolidSurface Material.

GREENGUARD Environment Institute (GEI)is an ANSI Authorized Standards Developer that oversees the GREENGUARDcertification program.? GEI establishesacceptable indoor air standards for indoor products, environments, andbuildings.

B. GREENGUARD Environmental Institute (GEI):

1. GREENGUARD listed and certified low emittingproducts.

C. International Association of Plumbing andMechanical Officials (IAPMO):

1. Universal Plumbing Code (cUPC US and Canada) approvals.

D. National Fire Protection Association (NFPA):

1. NFPA 70 - National Electrical Code.

E. PublicLaw 102-486, Energy Policy Act,requires that public lavatories manufactured after December 31, 1996, have flowrate or consumption not greater than 0.5 gpm (1.5 L/min.) or 0.25 gal. (0.95 L)per metering cycle.

F. Underwriters Laboratories, Inc.:

1. UL 1951 -Electric Plumbing Accessories.

1.4 ACTION SUBMITTALS

A. Product Data:?For each product indicated mounting requirements and rough-indimensions.? Mark each sheet with productdrawing designation.

Bradley Corporation's TerreonRE recycledsolid surface material contains 25-percent preconsumer recycled content and8-percent rapidly renewable material. LEED WE Credit 2 is for 50percent reduction in water use for building sewer, based on use ofwater-conserving fixtures documented under Credit WE 3.? LEED WE Credit 3 is for 30,35, or 40 percent reduction in water usage. Coordinate with Division 01requirements for LEED MR Credit 5 Regional Materials where applicable.

A. LEED Submittals:

1. Product Data for [Credit WE 2] [and] [Credit WE 3]:? Documentation indicating compliance withrequirements.

1.5 INFORMATION SUBMITTALS

A. Sample Warranty.

B. Operation, Care and Cleaning Instructions.

1.6 QUALITY ASSURANCE

A. Comply with Public Law 102-486 Energy PolicyAct.

A. Electrical Components:? Listed and labeled per NFPA 70,Article 100, by a testing agency acceptable to authorities havingjurisdiction.

1.7 WARRANTY

A. Special Manufacturer?s Warranty:? Provide manufacturer's standard form in whichmanufacturer agrees to repair or replace products that fail in materials orworkmanship.

1. Solid Surface Material:? 10 years.

2. Other Materials and Components:? One year.

PART 2 - PRODUCTS

2.1 MANUFACTURERS

A. Basis-of-Design Product:? Subject to compliance with requirements,provide temperature- actuated water mixing valves manufactured by BradleyCorporation, Menomonee Falls, WI 53051,(800)272-3539, fax (262)251-5817, www.bradleycorp.com.

Specifier:? Retain one ofthree paragraphs below based upon Project requirements.

1. Submit comparable products of one of thefollowing for approval by Architect:

a. [Insert name of manufacturer of comparableproducts].

2. Submit requests for substitution in accordancewith Instructions to Bidders and Division 01 General Requirements.

3. Provide specified product; Owner will notconsider substitution requests.

B. MATERIALS

Specifier: Certain Bradley wash fountains are formed fromBradley's own premium vandal-resistant densified solid surface material notedfor its resistance to chemicals, stains, burns and impacts. Surface damage canbe easily repaired with everyday cleansers or fine grit abrasives. First optionbelow describes Bradley Terreon, and second describes Terreon RE, a densifiedsolid surface material composed of a bio-based resin and preconsumer recycledgranules.

C. Lavatory Deck and Bowl Material:? Fabricate lavatory units from [thermosetacrylic modified polyester resin] [bio-based resin and preconsumer recycledgranules]certified by approved independent testing agency as complying with ANSI/ICPA‑SS-1-2001,ANSI Z124.3, and ANSI Z124.6, with the following minimum properties:

1. Basis of Design Product:? Bradley,[Terreon][Terreon RE]or a comparable product fabricated from one of the following materials:

a. DuPont, Corian Products.

b. Wilsonart International, Inc., GibraltarProducts.

2. Thickness:?1/2 inch (13 mm), minimum.

3. Liquid Absorption:? 0.025 percent in 24 hours, per ASTM D 570.

4. Tensile Strength:? 5000 psi (34 MPa), minimum, per ASTM D 638.

5. Thermal Expansion:? 2.30, per ASTM D 696.

6. Hardness:?55-60, per ASTM D 785.

7. Fire Resistance:?Class 1, per ASTM E 84.

2.2 WASHFOUNTAINS

Specifier: Bradley ClassicWashfountains described below are designed for efficient, heavy-duty handwashing requirements in institutional and manufacturing environments. Selectedunits are available meeting accessibility and juvenile height requirements.Several units include use of optional Bradley TerreonRE recycled content solidsurface material.

WF2500 Series are preassembled with Terreon solid surface materialbowls in semi-circular and circular configurations, with stainless steelpedestal panels.?

WF2600 Series consist of precast terrazzo bowls in semi-circularand circular configurations with stainless steel pedestal units.

WF2700 Series consist of stainless steel bowls in semi-circularand circular configurations with stainless steel pedestal units.

WF2800 Series are preassembled with Bradstone reinforced thermosetpolyester bowls in semi-circular and circular configurations with ABS taperedpedestal panels.

TDB3100 Series units consist of Terreon solid surface or TerreonRErecycled solid surface material bowls in circular configurations, withreinforced gel-coated fiberglass pedestal panels and stainless steel kickplate.

WF3200 Series extra height units consist of Terreon solid surfacematerial bowls in semi-circular and circular configurations, with reinforcedgel-coated fiberglass pedestal panels and stainless steel kick plate.

Select model and configuration, and edit below for options thatare available for the series and configuration desired. We recommend editingwith assistance of Bradley representative.

A. Floor-supported, [3] [4] [5] [8]-User [Accessible] Wash Fountain WFN#__:?Bowl constructed of [solid surface material] [recycled solid surface material] [reinforcedthermoset polyester] [precast terrazzo] [stainless steel]with steel legs and [stainless steel] [ABS] [fiberglass] pedestal panels [inpreassembled unit]. Include spray ring with stainless steel support tube,mixing valve, volume control valve, waste and supply connections with stop,strainer, and check valves. IPC/cUPC-certifed by IAPMO.

1. Basis of Design Manufacturer/Model:? Bradley,Classic Washfountain, [2500] [2600] [2700] [2800] [3100] [3200] series.

2. Bowl:? [Semi-circular] [Circular] [Corner], [36 inch(914 mm)][54 inch(1372 mm)]diameter, [7-1/2 inch(191 mm) deep] [8-1/2 inch (216 mm) deep] [9 inch(229 mm) deep] [, with backsplash].

3. Unit Height:?[28 inch (711 mm)] [29 inch (737 mm)][29-1/4 inch (743 mm)] [29-1/2 inch(749 mm)] [34 inch(864 mm)]

4. Spray Ring:?Non-sectional, with operating range of 20 to 80 psi (138 to552 kPa), flow rate as required by fixture size.

Specifier: Select one of four spray head valve activation optionsbelow.

a. Foot Control Operation:? Operation of foot rail activates hold-openvalve with slow closing upon release of rail.

b. Hand Control Operation:? Operation of pushbutton activates anair-metering valve with field-adjustable timing.

c. Infrared Sensor Operation:? Infrared sensing module and solenoid withadjustable turn off delay and automatic shut-off, with 110/24 VAC plug-intransformer.

d. Electronic Pushbutton/Timer Operation:? Electronic Pushbutton metering valve with110/24 VAC plug-in transformer.

Specifier: Manual mixing valve below is standard with unit.

5. Water Supply:?[Manualmixing valve][Singletempered line][Singleadjustable thermostatic mixing valve].

6. Drain and Supply Configuration:? [Off-line vent with supplies from below] [Centrallyrising vent with supplies from above] [Centrally rising vent with supplies frombelow][Off-linevent with supplies from above] [with stainless steel overhead piping shroud].

7. Accessories:

a. Soap Dispenser:?[Powderedsoap][Liquidsoap][,with metal cladding].

b. Paper Towel Dispenser:? Stainless steel, with tie pipe assembly, [single-fold] [c-fold].

c. Tie Pipe Assembly:? Vandal-resistant support tube reinforcement:bracket for accepting 1-1/2 inch diameter pipe.

d. Hose Bibb:?Loose key, threaded, solid brass, with polished chrome finish.

8. Bowl Color:?As selected by Architect from manufacturer's full line.

B. [Wall-Mounted] [Floor-supported],[3] [4] [5] [8]-User[Accessible,]Vandal-Resistant Shallow Bowl Washfountain WFN#__:? Preassembled bowl and pedestal unitconstructed of stainless steel with chrome plated exposed fittings. Includesindividual spray heads per station with stainless steel support tube, mixingvalve, volume control valve, waste and supply connections with stops,strainers, and check valves. Vandal-resistant construction with concealed sprayheads and connections, with support tube integrally welded to bowl.IPC/cUPC-certifed by IAPMO.

1. Basis of Design Manufacturer/Model:? Bradley,Sentry Washfountain, SN2000 series.

2. Bowl:? [Semi-circular] [Circular] [Corner], [36 inch(914 mm)][54 inch(1372 mm)]diameter, [5 inch (127 mm)] deep [, with backsplash].

3. Unit Height:?[34 inch(864 mm)]

4. Individual Spray Heads:? with operating range of 20 to 80 psi(138 to 552 kPa), flow rate is .5 GPM per station.

Specifier: Select one of four spray head valve activation optionsbelow.

a. Foot Control Operation:? Operation of foot pushbutton activateshold-open valve with slow closing upon release of pushbutton.

b. Hand Control Pushbutton Operation:? Operation of pushbutton activates an airmetering valve with field-adjustable timing.

c. Infrared Sensor Operation:? Infrared sensing module and solenoid withautomatic shut-off, with 110/24 VAC plug-in transformer.

Specifier: Manual mixing valve below is standard with unit.

5. Water Supply:?[Singletempered line][Singleadjustable thermostatic mixing valve] [Pressure balance mixing valve].

7. Accessories:

a. Soap Dispenser:?[Liquidsoap].

b. Paper Towel Dispenser:? Stainless steel, with tie pipe assembly, [single‑fold] [c‑fold].

c. Hose Bibb:?Loose key, threaded, solid brass, with polished chrome finish.

Specifier: BradleyMulti-Fount units described below feature a continuous Terreon or terrazzobowl with a matching spray head shelf. These easily-cleaned, highlyvandal-resistant units provide an efficient space-saving solution forheavy-duty hand washing in commercial and industrial facilities.

C. [Wall-mounted] [Wall-Mounted andFloor-Supported],Accessible, [2] [3] [4]User Washfountain WFN#__:? Constructed of [solid surface material] [recycledsolid surface material] [terrazzo] with integral continuous bowl, compact deck,and backsplash ledge containing concealed, vandal-resistant spray head [andliquid soap dispenser]. Unit includes waste and supply connectionsto wall with stop, strainer, and check valves, and steel support frame,concealed by tamper-resistant stainless steel access panel. ADA/ABA, and ANSIA117.1 compliant. IPC/cUPC-certifed by IAPMO.

1. Basis of Design Manufacturer/Model:? Bradley,Multi-Fount Washfountain System, MF 2900 series.

2. Unit Size:? [36 by 26 inch (914 by660 mm)] [46by 26 inch (1168 by 680 mm)] [26-3/4by 26-3/4 inch (679 by 679 mm) corner unit].

3. Spray Head:?Independent water stream former with flow rate of 0.5 gpm(0.032 L/s) at operating range of 20 to 80 psi (138 to 552 kPa).

Specifier: Select one of three spray head valve operation optionsbelow.

a. Spray Head Valve Operation:? Infrared sensing module and solenoid withadjustable turn off delay and automatic shut-off, ???? with110/24 VAC plug-in transformer

b. Spray Head Valve Operation:? Pushbutton air metering valve withfield-adjustable timing.

c. Spray Head Valve Operation:? Electronic pushbutton metering valve with110/24VAC plug-in transformer.

4. Water Supply:?[Singletempered line] [Singleadjustable thermostatic mixing valve].

5. Bowl/Spray Head/Pedestal Color:? As selected by Architect from manufacturer'sfull line.

D. Wall-Mounted, Accessible, Vandal-Resistant2-User Washfountain WFN#__:? Constructed of stainless steel with compact,crescent-shaped low-profile deck and backsplash ledge containing concealed,vandal-resistant spray heads. Preassembled unit includes waste and supplyconnections to wall with stop, strainer, and check valves, concealed bystainless steel access panel/trap cover. IPC/cUPC-certifed by IAPMO.

1. Basis of Design Manufacturer/Model:? Bradley,Bradmate Washfountain, S93-570 series.

2. Overall Unit Size:? 27-3/8 by 18-1/2 inches (695 by 470 mm).

3. Spray Head:?Independent water stream former with flow rate of 0.5 gpm(0.032 L/s) at operating range of 20 to 80 psi (138 to 552 kPa).

Specifier: Select one of three spray head valve operation optionsbelow.

a. Spray Head Valve Operation:? Infrared sensing module and solenoid withadjustable turn off delay and automatic shut-off, ???? with110/24 VAC plug-in transformer

b. Spray Head Valve Operation:? Pushbutton air metering valve withfield-adjustable timing.

c. Spray Head Valve Operation:? Electronic pushbutton metering valve with110/24VAC plug-in transformer.

Specifier: Manual mixing valve below is standard with unit.

4. Water Supply:?[Adjustable Thermostatic mixing valveassembly].

E. Multi-Station, [2] [3] [4] [5]-User Vandal-Resistant Wall Sink WFN#__:?Constructed of 14 ga. Type 304 stainless steel with reinforcingchannels. Frame constructed of 1-1/2 inch (38 mm) stainless steel tubing withadjustable height floor flanges. Preassembled unit includes drain spud and domegrate strainer and 1-1/2 (38 mm) inch diameter tailpiece.

1. Basis of Design Manufacturer/Model:? Bradley,Multistation Wall Sink.

2. Fixture Size:?[48by 18 inch (1219 by 457 mm)] [62 by 18 inch (1575 by 457 mm)] [80by 18 inch (2032 by 457 mm)] [102 by 18 inch (2591 by 457 mm)].

3. Faucet:? [PushbuttonMetering Faucet. Basis of Design Manufacturer/Model:? Bradley, Model 90-75] [Specifier insert faucetselection].

F. Multi-Station, 8-User Vandal-Resistant IslandSink WFN#__:? Constructed of 14 ga. Type 304 stainlesssteel with reinforcing channels and sound deadening material on underside.Frame constructed of 1-1/2 inch (38 mm) stainless steel tubing with adjustableheight floor flanges. Column-mounted stainless steel valve manifold housing.Preassembled unit includes drain spud and dome grate strainer and 1-1/2 (38 mm)inch diameter tailpiece.

1. Basis of Design Manufacturer/Model:? Bradley,Multistation Island Sink.

2. Fixture Size:?[30by 72 inch (762 by 1829 mm)] [40 by 72 inch (1016 by 1829 mm)].

3. Faucet:? [PushbuttonMetering Faucet. Basis of Design Manufacturer/Model:? Bradley, Model 90-75] [Specifier insert faucetselection].

PART 3 - EXECUTION

3.1 INSTALLATION

A. Assemble fixtures and associated fittings andtrim in accordance with manufacturer's instructions.

B. Install fixture supports attached to buildingstructure for fixtures requiring supports.

C. Install fixtures onto waste-fitting seals orflanges and attach to supports or building structure.

D. Install fixtures level, plumb, and firmly inplace in accordance with manufacturer's rough-in drawings.

E. Install water supply piping to each fixturerequiring water supply connection. Provide stop on each supply inreadily-serviced location. Fasten supply piping to supports or substrate.

F. Install trap and waste piping to each fixturerequiring sanitary system connection.

G. Install escutcheons at exposed pipingpenetrations in finished locations and within cabinets.

H. Seal joints between fixtures and walls, floors,and countertops with mildew-resistant silicone sealant.

3.2 FIELD QUALITY CONTROL

A. Verify fixtures are correct categories and typesspecified at locations where installed. Verify installed heights and clearancesmeet requirements of authorities having jurisdiction.

3.3 CLEANING AND PROTECTION

A. Repair or replace defective work, includingdamaged fixtures and components.

B. Clean unit surfaces, test fixtures, and leave inready-to-use condition.

C. Install new batteries in battery-operateddevices at time of Substantial Completion.

D. Turn over keys, tools, maintenance instructions,and maintenance stock to Owner.

E. Protect units with water-resistant temporarycovering. Do not allow temporary use of plumbing fixtures unless approved inwriting by Architect. Remove protection at Substantial Completion and dispose.

END OF SECTION