Specifiernotes are shown in italics and should be deleted from the final document.? Generally all of the manufacturer?s productsin this category are listed and the specifier must take care to delete thoseproducts not included in the project.

 

Dependingon the relative complexity of the project, the specifier may choose to combinetwo or more Locker Sections into one Section, Section 10500 - Lockers,corresponding to the CSI MasterFormat?.

 

Editeach Article in this Section to suit project requirements.

 

 

SECTION10520

 

PLASTIC LOCKERS

 

 

PART 1 GENERAL

 

1.01   SECTIONINCLUDES

 

A.             Solidplastic lockers.

B.             Solidplastic Z lockers.

C.             Solidplastic gear lockers.

D.             Solidplastic bench lockers.

E.             Solidplastic cubby lockers.

F.             Pedestalbenches.

G.?? Hardware and accessories.

 

1.02   RELATEDSECTIONS

 

A.             Section(select Sections that describe theanchoring substrate: floor and/or walls).

 

1.03   REFERENCES???

 

A.             ADA Accessibility Guidelines for Buildingsand Facilities.

 

1.04   SUBMITTALS

 

A.             Providesubmittals in accordance with Conditions of the Contract and Section01330-Submittal Procedures.

B.             Submitshop drawings showing locker plan layout, numbering plan, profiles, and productcomponents, including anchorage, accessories and finish colors.

C.             Submitproduct data on locker construction, hardware, and accessories.

D.             Submittwo samples 4 x 4 inch (100 x 100 mm) in size illustrating finish and color.

E.             Submitmaintenance data for installed products in accordance with Section01780-Closeout Submittals.

 

1.05   DELIVERY,STORAGE AND HANDLING

 

A.             Generallycomply with provisions of Section 01600-Product Requirements.

B.             Complywith manufacturer?s ordering instructions and lead time requirements to avoidconstruction delays.

C.             Delivermaterials in manufacturer?s original, unopened, undamaged containers withidentification labels intact.

D.             Store lockersindoors, protected from weather conditions and construction activities.

 

1.06   PROJECTCONDITIONS

 

A.             Buildingenclosed, completely protected from outside weather with minimum insidetemperature of 60?F.

 

1.07   WARRANTY

 

A.             Providemanufacturer?s twenty year warranty against rust, delamination or breakage ofplastic components.

 

PART 2 PRODUCTS

 

2.01   MANUFACTURERS

 

A.             TheMills Company, a subsidiary of Bradley Corporation, P.O. Box 309, MenomoneeFalls, WI 53052-0309.? Phone 800-BRADLEY(800-272-3539), FAX 262-251-5817.? http://www.bradleycorp.com

B.             Substitutions:[Comply with Section 01600 ? Product Requirements] [Not Permitted].

 

2.02   MANUFACTUREDUNITS

 

A.             ModelLENOXLOCKER lockers, [60 inch (1524 mm)] [72 inch (1829 mm) high x [12 inch(305 mm)] [15 inch (381 mm)] [18 inch (457 mm)] wide x [12 inch (305 mm)] [15inch (381 mm)] [18 inch (457 mm) deep, [1] [2] [3] [4] [5] tier [6 tier (72 inch model only)], (specify from standard and optionalselections).

B.             ModelLENOXZLOCKER lockers, [60 inch (1524 mm)] [72 inch (1829 mm) high x [15 inch(381 mm)] [18 inch (457 mm)] wide x [12 inch (305 mm)] [15 inch (381 mm)] [18inch (457 mm) deep, [2] tier, (specify from standard and optional selections).

C.             ModelLENOXGEAR gear lockers, [72 inch (1829 mm) high x [24 inch (610 mm)] [30 inch(762 mm)] [36 inch (914 mm)] wide x [18 inch (457 mm)] [21 inch (533 mm)] [24inch (610 mm)] deep, (specify fromstandard and optional selections).

D.             ModelLENOXBENCH bench lockers, 20 inch (508 mm) high x 12 inch (254 mm) wide x 12inch (254 mm) deep, (specify from standardand optional selections).

E.             ModelLENOXCUBBY cubby lockers, [60 inch (1524 mm)] [72 inch (1829 mm)] high x [12inch (305 mm)] [15 inch (381 mm)] [18 inch (457 mm) wide x [12 inch (305 mm)][15 inch (381 mm)] [18 inch (457 mm) deep, [2] [3] [4] [5] tier [6 tier (72 inch model only)], (specify from standard and optionalselections).

F.             ModelLENOXPEDSTAL pedestal bench, 20 inch (508 mm) high x [9 1/2 inch (241 mm)] [12inch (305 mm)] [18 inch (457 mm)] [24 inch (610 mm)]wide, (specify from standard selections).

 

2.03   COMPONENTS

 

A.?? LENOXLOCKER, LENOXZLOCKER, LENOXCUBBY

1.                 Lockermaterial: Sides, backs, shelves, tops, bottoms, doors, door frames andcontinuous latch constructed from high-density polyethylene (HDPE).

a.             Sides,shelves, tops, bottoms and backs fabricated from 3/8 inch (10 mm) HDPE.

b.             Doors,door frames and continuous latch fabricated from ? inch (13 mm) HDPE.

c.             Slopetops fabricated from a single sheet of 3/8 inch (10 mm) HDPE.

d.             Basesfabricated from 1/2 inch (13 mm) HDPE.

e.             Endpanels and flat top fabricated from ? inch (13 mm) HDPE.

2.                 Doorhinge: Continuous piano hinge fabricated from 16 gauge type 304 stainlesssteel.

B.?? GEARLOCKER

1.             Lockermaterial: Sides, backs, shelves, tops, bottoms, doors, door frames andcontinuous latch constructed from high-density polyethylene (HDPE).

a.             Sides,shelves, tops, bottoms, backs, doors, door frames and continuous latchfabricated from 1/2 inch (13 mm) HDPE.

b.             Footlocker / bench seat, frame and front fabricated from 1 inch (25 mm) HDPE.

c.             Installationtrim fabricated from 1 inch (25 mm) HDPE.

C.             LENOXPEDESTAL

1.             Pedestalbench: Top fabricated from 1 1/2 inch (38 mm) thick HDPE, pedestals 18 ? inch(470 mm) black anodized aluminum with welded aluminum flanges.

D.             LENOXBENCH

1.             Lockerbench top: 1 inch (25 mm) thick HDPE.

 

2.04 HARDWAREAND ACCESSORIES

 

A.?? LENOXLOCKER,LENOXZLOCKER, LENOXCUBBY

1.                 Provideone plastic double coat hook for each opening in one, two tier and z lockers.

2.                 Provideone number plate for each opening.

3.                 Providescrews, anchors and angle brackets for locker base installation.

B.             LENOXGEAR

1.             Providefour black powder coated zinc die cast wall hooks for each opening.

2.             Provideone number plate for upper locker.

3.             ProvideSoft Down Stay for bench seat.

4.             Providefasteners for installation trim.

C.??LENOXPEDESTAL

1.             Providehardware for attaching bench top to pedestals and anchoring pedestals to floor.

 

2.05 FABRICATION

 

A.?? LENOXLOCKER, LENOXZLOCKER, LENOXCUBBY

1.             Lockerbox fabricated from a single sheet of HDPE with corners fused together.? Weld frame and shelves to box assembly.

2.             Attachhinge to door and frame with vandal-resistant double threaded stainless steelscrews.

3.             Continuouslatch securely attached to the entire length of the door with stainless steelscrews, providing a full length latching mechanism capable of accepting severallock types.

4.             Fabricateslope top from a single sheet of HDPE, grooved to permit bending to form abacking strip for attachment to wall.

5.             Lockingdevice: [Hasp] [Built in key lock] [Built-in combination lock] [Coin/tokenoperated lock] [Keypad lock].

6.             Provide[openings at top and bottom of each door] [mesh door] for ventilation.

7.             Base:[3] [4] inch high.

8.             Endpanels: [Flat top] [Slope top] for [single] [double] locker configuration.

9.             Factoryfinish:

a.             Tops,bottoms, side walls, backs and shelves, smooth white commercial grade.

b.             Door,door frames and continuous latch, slightly textured matte finish, colorselected from manufacturer?s standard.

c.             Hingepowdercoated to match door and frame.

d.             Basecolor: [Black] [(select special color)].

e.             Endpanel color selected from manufacturer?s standard.

B.??LENOXGEAR

1.             Upperbox fabricated from a single sheet of HDPE with corners fused together. Weldframe and shelves to box assembly.

2.             Attachhinge to door and frame with vandal-resistant double threaded stainless steelscrews.

3.             Continuouslatch securely attached to the entire length of the door with stainless steelscrews, providing a full length latching mechanism capable of accepting severallock types.

4.             Footlocker / bench seat fastened to upper box assembly with security fasteners.

5.             Lockingdevice for locker and footlocker: [Hasp]

6.             Sideventilation: [Mesh] [Solid]

7.             Factoryfinish:

a.             Door,and door frames, cobblestone textured matte finish, color selected frommanufacturer?s standard.

b.             Hinge powdercoated to match door and frame.

 

 

PART 3 EXECUTION

 

3.01   EXAMINATION

 

A.             Verifythat locker area is ready for installation.

B.             Verifyfield measurements are as shown on approved shop drawings.

C.             Verifythat bases are properly, leveled, sized and in correct location.

D.             Verifycorrect location of built-in framing and blocking.

 

3.02   INSTALLATION

 

A.             Complywith manufacturer?s written instructions for installation of lockers [andbases].? Install plumb and square.

B.             Anchorlocker units to wall through the locker back with suitable anchor devices forthe substrate.

C.             Anchorlocker units to floor [base for islandapplications] with hardware furnished by manufacturer.

D.             Through-boltadjoining locker units together to provide rigid installation.

E.             Installaccessories, [number plates,] [end panels,] [sloped tops,] [and flat tops].

 

3.03   ADJUSTING

 

A.             Section01700 ? Execution Requirements: Testing, adjusting, and balancing.

B.             Adjustand align components to operate smoothly.

C.             Correctminor damage to installed products; remove and replace work that cannot besatisfactorily repaired.

 

3.04   CLEANING

 

A.             Section01700 ? Execution Requirements: Final cleaning.

B.             Cleanlocker interiors and exterior surfaces.

C.             Removepackaging and construction debris, and legally dispose of off-site.

 

3.05   SCHEDULE

 

(Where specified locker units vary in tiernumber, depth, color, etc., it might be best to give them a ?mark? and create a schedule).

 

END OF SECTION