Plumbing Fixtures

Yes, there are two kits available. One is S65-110 that replaces the "wet" parts. The other is S73-054A. This replaces all the S65-110 does as well as the plastic upper body excluding the brass casting. It is better of the two.

This is not an individual part, it is part of the leg. The part number for the strainer is 173-002 and for the screw is 160-042.

This is not an individual part, but part of the leg itself. The leg for a standard height washfountain is 193-002. For a juvenile height washfountain, it is 193-002B.

First, you will have to disassemble your washfountain to get to the sprayhead. To clean the sprayhead, remove the three screws holding the sprayhead together. Disassemble the sprayhead and dislodge chips, pipe dope or other foreign material with a wire brush. Lime build-up may also be removed in this manner. Spayheads with rubber grommet spray rings may be cleaned by rubbing a coin over the grommet to remove the deposits.

Called a volume control handle, its part number is 128-009A. A complete parts breakdown for your hand-controlled fixture is available to you on this Website under Plumbing Fixtures/Washfountains/Classic deep bowl.

Yes, we continue to sell parts for washfountains that are well over 50 years old and still working. You will need to determine what model and style you have. To help in determining what you have, visit the Product Information: Plumbing Fixtures section of this web site. Scroll the listing and select a model and click "display product". This will allow you to visualize the models and determine what you have. You will then see more choices for each model group covering different features. After you narrow down what you have, you can view technical data and/or installation instructions. The installation instructions so show parts breakdowns. Parts can be ordered from the nearest sales representative, who can be found on our web site under customer service.

Bradley recommends a product called "Super Lube Grease" manufactured by Synco Chemical Corporation. Contact them at 516-567-5300. The foot valve itself is S07-015. The repair kit for it is S65-001A.

Yes, the aerator can be purchased separately, and the part number is S05-140.

Bradley works directly with a company called Champion Brand Products (a division of Lochrie and Associates, Inc.). They have tested all of our soap valves and can give you proper recommendations for the specific types of soap necessary for any application. The phone number for Champion Brand Products 1(800)344-5301.

The style of streamformer depends on the type of valving the multi-fount is equipped with. Multi-Fount with 90-75 metering valves use streamformer 115-125.Those equipped with air or infrared valves us 115-131.

This is the filler cap for the soap tank. This part number is 136-011. To remove this cap requires a spanner wrench, 130-142. This same cap is also used on Crescents, Images, Corner-Fount and Quad-Fount

Contact you local Bradley representative for assistance in ordering genuine Bradley parts. A serial number gives us an idea of how old your fixture is, but does not identify it. You may need to know the following when ordering replacement parts:

1. Shape: Circular, semi-circular or corner
2. Bowl Material: Precast Terrazzo, Bradstone, or Stainless steel, Terreon solid surface.
3. Water Activation: Foot control, hand-control, electronic or air
4. Supply & Vent: Water supply for above or below, vent off the line or centrally rising
5. If no serial number, estimated date of installation

We offer a soap retrofit kit, part #S45-1467. Circular washfountains require two (2) kits, which include two (2) soap tanks and four (4) soap valves. Semi-circular washfountains require one (1) kit, which includes one (1) soap tank and two (2) soap valves. Complete instruction sheets will be provided with each retrofit kit

There are two different gaskets. Part number 125-011 is used for precast Terrazzo, Terreon solid surface and Bradstone. For stainless steel bowls use part number 125-008.

The instruction sheet for the Accu-Zone (AZ) conversion kit is 215-840. This information is provided with the conversion kit. This instruction sheet is not currently available on the Website. You will need to request one from our Technical Service department or through your local Bradley representative.

The thermostatic mixing valve S01-116S can replace the manual-mixing valve (S01-038). This includes the valve and a tailpiece prepack.

It regulates the amount of water entering the valve to push the plunger down for shut off. For example, if the needle valve is screwed in all the way, the valve will not shut off. When it is screwed out all the way, it has a quick shut off (automatically 1 second), but without slamming.

The S27-016 vernatherm valve is obsolete. Its replacement is the S0l-116. All internal parts are interchangeable with the exception of the cold water seat (153-003), cold water retainer (158-004) and main slider (S27-018). The original body and cover are no longer available. If these two parts are required, then a complete new valve is needed.

A repair kit, S45-049, is available and will repair either of the valves

Following are all the conversion kits available for different supply and vent configurations on classic washfountains. The kits can be used on circular as well as semi-circular models.

This is not an individual part, it is part of the leg. The part number for standard height is 193-002, and for juvenile height is 193-002B.

Yes, we do offer a Terrazzo resurfacing kit. It includes most of the materials necessary to resurface a 54 circular bowl. The bowl must be thoroughly cleaned and dried before proceeding. The part number is S65-119 and instructions are included.

For colors use kits that include pigments. Whisper Gray requires S65-120, Granito is kit S65-121, Green is S65-122 and Dusty Rose is S65-124.

After resurfacing, use a marine grade polyurethane coating (not supplied) to seal the bowl and bring back that new glossy finish.

Note: If bowl is deteriorating to the point it is leaking, it should be replaced

By design, the Touch 'N' Flo valve does drip water from the pushbutton. When the pushbutton is activated, water is evacuated from the upper chamber inside the valve body. This water is then directed to spill out small holes on the pushbutton of the valve. There will be no more than a teaspoon each time the valve is activated. This is a standard function of the valve and is not a cause for alarm. If a more serious problem persists, contact your Bradley representative.

Based on the information you have provided, you have an Eaton solenoid valve, 269-719. The repair kit is S65-113. This kit consists of the spring, an armature and a diaphragm.

The part number for the integral check stop is #S27-102. No repair kit or parts are available for this valve. This information is available on pages 14 & 15 of the Shower Operation and Service Guides, which is available on this web site, under the Technical Data section. Also, this integral stop is optional equipment on the Equa Flo valve.

The part number for the #443 showerhead is #S24-038. Additional information is available on pages 3, 9, 37, and 38 of the Shower Operation and Service Guides, which is available on this web site under the Technical Data Section.

Depending on how old the column is, you will either require S24-008, which is provided from 1961 to 1974, or S24-072 which is the current showerhead.